Water Overlay Wizard: Difference between revisions

Latest revision as of 11:39, 26 April 2024

Flooding Wizard Introduction Page

This configuration wizard is a special interface which helps to guide the configuration of a Water Overlay. Across multiple steps, it progresses through each type of Data which can be configured, along with the most important attributes of the overlay.

Editor → Current Situation (Ribbon tab) → Overlays (Ribbon bar) → Water Overlay (Left panel) → Configuration Wizard (Right panel)

Each of the Water Overlay variants has a configuration wizard which helps the user with configuring the overlay. The general structure of the wizard is the same for all variants, with the exception that for flooding overlays a step for configuring a breach area is included and for the groundwater overlays a step for configuring an aquifer area is included.

When the wizard has been completed once, it can be reopened at any time, and any step can be accessed anew.

Step 1: Weather

Step 1: Weather event

The weather event defines the total simulation time and the weather and climate effects during the simulation. Specifically, the amount of rain and when it falls during the simulation, as well as the evaporation which takes place

Step 2: Water system

Step 2: Setup Water System

The water system is the most complex step of the configuration and contains a multitude of substeps to configure all geographical data. Its various components can be configured in the following order:

Breach (flooding overlays only): A breach area, a location where an (uncontrolled) inflow of water takes places.

Water areas: Water areas, defined regions in which a specific water level is maintained. It is also possible to have the wizard generate a single water area for the entire project area.

Ground water: Ground water, supplied as the distance between the ground water level and the datum. A GeoTIFF can be imported.

Bottom Boundary: Bottom pressure and resistance, supplied as two prequel Grid Overlays which can be imported (Groundwater Overlay only).

Sewers: Sewer areas, the broad definitions for where what kind of sewers exist. It is also possible to have the wizard generate sewer areas based on the neighborhoods in the project area.

Inundation areas: Inundation areas, definitions of water on the surface, in the form of inundated land. It is also possible to have the wizard generate a single inundation area covering the entire project area.

Aquifer areas (groundwater overlays only): Aquifer areas, definitions for transmissivity or hydraulic conductivity of the ground layer.

Weirs: Weirs, minor barriers in the water flow.

Culverts: Culverts, tunnels which form direct connections between two locations.

Pumps: Pumps, structures which move water from a lower to a higher location.

Inlets: Inlets, structures which add or remove water.

Sewer overflows: Sewer overflows, points where water from sewers can flow back onto the surface.

All of the above components can be imported or connected to the hydrological model.

Breach Area
Water Areas
Ground Water
Bottom boundary flow
Sewers
Inundation Areas
Aquifer Areas
Weirs
Culverts
Pumps
Inlets
Sewer Overflows

Feedback

In the Water Overlay Wizard you can encounter several of the components highlighted yellow (warning) or red (error). This feedback is provided to help you configure the modelled water system to make it fully functional in the Tygron Platform and provide information about the configured settings and imported data. Any errors in the imported data for example will be highlighted. When selecting a step which is highligthed yellow or red, the drop-down menu will automatically place the warnings and errors at the top of the menu. When selecting one of these from the menu, feedback about the warning or error is displayed in the wizard. To solve these issues, possible fixes are proposed which can be automatically applied when accepted. The possible fixes are depicted with the tool icon. By clicking on this icon, the fix is proposed and can be applied.
See also How to apply fixes for multiple components in the Water Overlay Wizard.

Step 3: Hydrological coefficients

Hydrological coefficients are values of existing elements of the world, specifically terrain and constructions. The coefficients dictate the ability of water to flow between cells and layers. The following data can be configured:

Surface terrain: For the surface terrains, attributes can be adjusted directly.

Ground terrain: For the ground terrains, attributes can be adjusted directly as well.

Constructions: For constructions, the wizard links to the function values editing screen, and will open with focus on "WATER" related functions.

Surface terrain
Ground terrain
Constructions

Step 4: Interaction

The wizard provides a few options to automatically generate methods of interaction with the hydrological model. The system visualization can be activated or deactivated. Additionally, for some hydrological constructions and features panels can be generated which allow for their most important attributes during a session.

Step 5: Output overlays

Multiple result types are available. In the wizard multiple result types can be selected. One result type (indicated with the "First" checkbox) will be the main overlay's result type. The other selections will become result type child overlays. Relevant attributes can be modified as well, if they are related to selected result types.

Finally, the TIMEFRAMES attribute can be configured here as well, defining the amount of result snapshots which should be made during the calculation.

Step 6: Input overlays

To gain more insight into the data used by the model, you may opt to add one or more input overlays as well. These add Average Overlays that are configured for the geographical display of attribute values relevant for the calculation of the water model.

@@ Line 1: / Line 1: @@
 __NOTOC__
 [[File:FloodingWizardIntroduction1.jpg|thumb|200px|Flooding Wizard Introduction Page]]
-The configuration wizard is a special interface which helps to guide the configuration of the overlay. Across multiple steps, it progresses through each type of [[GEO Data|Data]] which can be configured, along with the most important [[Attributes|attributes]] of the overlay.
+This configuration wizard is a special interface which helps to guide the configuration of a [[Water Overlay]]. Across multiple steps, it progresses through each type of [[GEO Data|Data]] which can be configured, along with the most important [[attribute]]s of the overlay.
-{{Editor ribbon|header=Current situation|bar=Overlays|left panel=The overlay|right panel=Configuration wizard}}
+{{Editor location|overlay wizard|Water Overlay}}
-Each of the water overlay variants has a configuration wizard which helps the user with configuring the overlay. The general structure of the wizard is the same for all variants, with the exception that for '''[[Flooding_(Overlay)|flooding overlays]]''' a step for configuring a [[Breach (Water Overlay)|breach]] area is included as well.
+Each of the [[Water Overlay]] variants has a configuration wizard which helps the user with configuring the overlay. The general structure of the wizard is the same for all variants, with the exception that for [[Flooding_(Overlay)|flooding overlay]]s a step for configuring a [[Breach (Water Overlay)|breach]] area is included and for the [[Groundwater (Overlay)|groundwater overlay]]s a step for configuring an [[Aquifer (Water Overlay)|aquifer area]] is included.
-When the wizard has been completed once, it can be reopened at any time, and any step can be accessed anew.<br clear=all>
+When the wizard has been completed once, it can be reopened at any time, and any step can be accessed anew.
+{{clear}}
 ===Step 1: Weather===
 [[File:GroundWaterOverlayWeatherEvent1.jpg|thumb|200px|Step 1: Weather event]]
-The [[Weather|weather event]] defines the total simulation time and the weather and climate effects during the simulation. Specifically, the amount of rain and when it falls during the simulation, as well as the evaporation which takes place.<br clear=all>
+The [[Weather|weather event]] defines the total simulation time and the weather and climate effects during the simulation. Specifically, the amount of rain and when it falls during the simulation, as well as the evaporation which takes place
+{{clear}}
 ===Step 2: Water system===
 [[File:FloodingOverlaySetUpWaterSystem1.jpg|thumb|200px|Step 2: Setup Water System]]
 The water system is the most complex step of the configuration and contains a multitude of substeps to configure all geographical data. Its various components can be configured in the following order:
-: '''Breach''' (flooding overlays only): A breach area, a location where an (uncontrolled) inflow of water takes places.
+: '''Breach''' (flooding overlays only): A [[Breach_(Water_Overlay)|breach area]], a location where an (uncontrolled) inflow of water takes places.
-: '''Water areas''': [[Water level area (Water Overlay)|Water level areas]], defined regions in which a specific water level is maintained. It is also possible to have the wizard generate a single water level area for the entire project area.
+: '''Water areas''': [[Water area (Water Overlay)|Water areas]], defined regions in which a specific water level is maintained. It is also possible to have the wizard generate a single water area for the entire project area.
-: '''Ground water''': [[Underground model (Water Overlay)|Ground water]], the height of the underground saturated by water relative to {{datum}}. A [[Geotiff (Overlay)|GeoTIFF]] can be [[Geo Data Wizard|imported]].
+: '''Ground water''': [[Ground model (Water Overlay)|Ground water]], supplied as the distance between the ground water level and the {{datum}}. A [[GeoTIFF]] can be [[Geo Data Wizard|imported]].
+: '''Bottom Boundary''': [[Bottom pressure prequel (Water Overlay)|Bottom pressure]] and [[Bottom resistance prequel (Water Overlay)|resistance]], supplied as two prequel [[Grid Overlay]]s which can be [[Geo Data Wizard|imported]] ([[Groundwater Overlay]] only).
 : '''Sewers''': [[Sewer area (Water Overlay)|Sewer areas]], the broad definitions for where what kind of sewers exist. It is also possible to have the wizard generate sewer areas based on the [[neighborhood]]s in the project area.
 : '''Inundation areas''': [[Inundation area (Water Overlay)|Inundation areas]], definitions of water on the surface, in the form of inundated land. It is also possible to have the wizard generate a single inundation area covering the entire project area.
-: '''Aquifer areas''' ([[Groundwater_(Overlay)|groundwater overlays]] only): [[Aquifer (Water Overlay)|Aquifer areas]], definitions for transmissivity or hydraulic conductivity of the underground layer.
+: '''Aquifer areas''' ([[Groundwater (Overlay)|groundwater overlays]] only): [[Aquifer (Water Overlay)|Aquifer areas]], definitions for transmissivity or hydraulic conductivity of the ground layer.
 : '''Weirs''': [[Weir (Water Overlay)|Weirs]], minor barriers in the water flow.
-: '''Culverts''': Culvert (Water Overlay)|Culverts]], tunnels which form direct connections between two locations.
+: '''Culverts''': [[Culvert (Water Overlay)|Culverts]], tunnels which form direct connections between two locations.
 : '''Pumps''': [[Pump (Water Overlay)|Pumps]], structures which move water from a lower to a higher location.
 : '''Inlets''': [[Inlet (Water Overlay)|Inlets]], structures which add or remove water.
@@ Line 32: / Line 35: @@
 File:FloodingOverlayWizardWaterAreas1.jpg|Water Areas
 File:FloodingOverlayWizardGroundWater1.jpg|Ground Water
+File:bottom_boundary_wizard.jpg|Bottom boundary flow
 File:FloodingOverlayWizardSewers1.jpg|Sewers
 File:FloodingOverlayWizardInundationAreas1.jpg|Inundation Areas
@@ Line 40: / Line 44: @@
 File:FloodingOverlayWizardInlets1.jpg|Inlets
 File:FloodingOverlayWizardSewerOverflows1.jpg|Sewer Overflows
-</gallery><br clear=all>
+</gallery>
+{{clear}}
+===Feedback===
+In the Water Overlay Wizard you can encounter several of the components highlighted yellow (warning) or red (error). This feedback is provided to help you configure the modelled water system to make it fully functional in the {{software}} and provide information about the configured settings and imported data. Any errors in the imported data for example will be highlighted.
+When selecting a step which is highligthed yellow or red, the drop-down menu will automatically place the warnings and errors at the top of the menu. When selecting one of these from the menu, feedback about the warning or error is displayed in the wizard.
+To solve these issues, possible fixes are proposed which can be automatically applied when accepted. The possible fixes are depicted with the tool icon. By clicking on this icon, the fix is proposed and can be applied. <br>
+See also [[How to apply fixes for multiple components in the Water Overlay Wizard]].
+[[File:Warning_in_wizard.PNG|left|400px|Warning in the wizard]]
+{{clear}}
 ===Step 3: Hydrological coefficients===
 [[File:FloodingOverlayHydrologiCoefficients1.jpg|thumb|200px|Step 3: Hydrological coefficients]]
-Hydrological coefficients are values of existing elements of the world, specifically {{inlink|lcase=1|Terrain}} and {{inlink|Miscellaneous hydrological properties of constructions|constructions}}. The coefficients dictate the ability of water to flow between cells and layers. The following data can be configured:
+Hydrological coefficients are values of existing elements of the world, specifically [[Terrain|terrain]] and [[Hydrological attributes of constructions (Water Overlay)|constructions]]. The coefficients dictate the ability of water to flow between cells and layers. The following data can be configured:
-: '''Surface terrain''': For the surface {{inlink|lcase=1|Terrain}}s, attributes can be adjusted directly.
+: '''Surface terrain''': For the surface terrains, attributes can be adjusted directly.
-: '''Underground terrain''': For the underground {{inlink|lcase=1|Terrain}}s, attributes can be adjusted directly as well.
+: '''Ground terrain''': For the ground terrains, attributes can be adjusted directly as well.
-: '''Constructions''': For {{inlink|Miscellaneous hydrological properties of constructions|constructions}}, the wizard links to the [[function values]] editing screen, and will open it the "WATER" filter for the values to display.
+: '''Constructions''': For constructions, the wizard links to the [[Functions#Function values|function values]] editing screen, and will open with focus on "WATER" related functions.
 <gallery widths=75px heights=75px>
 File:FloodingOverlayWizardSurfaceTerrain1.jpg|Surface terrain
-File:FloodingOverlayWizardUndergroundTerrain1.jpg|Underground terrain
+File:FloodingOverlayWizardUndergroundTerrain1.jpg|Ground terrain
 File:FloodingOverlayWizardConstructions1.jpg|Constructions
-</gallery><br clear=all>
+</gallery>
+{{clear}}
 ===Step 4: Interaction===
 [[File:FloodingOverlayWizardInteraction1.jpg|thumb|200px|Step 4: Interaction]]
-The wizard provides a few options to automatically generate methods of interaction with the hydrological model. The {{inlink|lcase=1|System visualization}} can be activated or deactivated. Additionally, for some hydrological constructions and features panels can be generated which allow for their most important attributes during a [[session]].<br clear=all><!--
+The wizard provides a few options to automatically generate methods of interaction with the hydrological model. The [[System_visualization_(Water_Overlay)|system visualization]] can be activated or deactivated. Additionally, for some hydrological constructions and features panels can be generated which allow for their most important attributes during a [[session]].<!--
 : '''System visualisation''':
 : '''Interaction panels''':
 -->
+{{clear}}
 ===Step 5: Output overlays===
 [[File:FloodingOverlayWizardOutputOverlays1.jpg|thumb|200px|Step 5: Output overlays]]
-Multiple {{inlink|lcase=1|Result type}}s are available. In the wizard multiple result types can be selected. One result type (indicated with the "First" checkbox) will be the main overlay's result type. The other selections will become {{inlink|lcase=1|Result child overlays}}. Relevant attributes can be modified as well, if they are related to selected result types.
+Multiple [[Result type (Water Overlay)|result types]] are available. In the wizard multiple result types can be selected. One result type (indicated with the "First" checkbox) will be the main overlay's result type. The other selections will become [[Result type (Water Overlay)#Multiple result child overlays|result type child overlays]]. Relevant attributes can be modified as well, if they are related to selected result types.
+Finally, the [[Timeframes (Water Overlay)|TIMEFRAMES]] attribute can be configured here as well, defining the amount of result snapshots which should be made during the calculation.
+{{clear}}
-Finally, the {{inlink|TIMEFRAMES}} attribute can be configured here as well, defining the amount of result snapshots which should be made during the calculation.<br clear=all>
 ===Step 6: Input overlays===
-[[File:FloodingOverlayWizardInputOverlays1.jpg|thumb|200px|Step 5: Input overlays]]
+[[File:FloodingOverlayWizardInputOverlays1.jpg|thumb|200px|Step 6: Input overlays]]
-To gain more insight into the data used by the model, you may opt to add one or more {{inlink|lcase=1|Input overlay}}s as well. These add [[Average Overlay]]s configured for the geographical display of attribute values relevant for the calculation of the water model.<br clear=all>
+To gain more insight into the data used by the model, you may opt to add one or more [[input overlay]]s as well. These add [[Average Overlay]]s that are configured for the geographical display of attribute values relevant for the calculation of the water model.
+{{clear}}
+[[Category:Wizards]]