Weir height test case (Water Module): Difference between revisions

From Tygron Preview Support Wiki
Jump to navigation Jump to search
Line 96: Line 96:
* Output results: [[Surface last value result type (Water Overlay)|Surface last value]], [[Surface last datum result type (Water Overlay)|Surface last datum]] and [[Surface last datum result type (Water Overlay)|Surface elevation]]
* Output results: [[Surface last value result type (Water Overlay)|Surface last value]], [[Surface last datum result type (Water Overlay)|Surface last datum]] and [[Surface last datum result type (Water Overlay)|Surface elevation]]


==Output as required==
==Output==
*Software package used: {{software}}
Measured object graphs are displayed below:
*Numerical scheme: FV (Kurganov, Bollerman, Horvath)*
*Specification of hardware used to undertake the simulation:
** Processor: Intel Xeon @2.10GHz x 8,
** RAM 62.8 GiB,
** GPU: 2x NVidia 1080
** Operating system: Linux 4.13
*Time increment used: adaptive: 0.25 - 1.13 s.
*Grid resolution: 10 m.
*Simulation time: 28s.
*Remaining volume water: 10050 m3
 
Measured point graphs are displayed below:
<ul>
<ul>
<li style = "display:inline-block">[[File:graph_p1_case1_ukbm.png|x400px|border]]</li>
<li style = "display:inline-block">[[File:graph_p1_case1_ukbm.png|x400px|border]]</li>
Line 122: Line 110:


{{article end
{{article end
|notes=  
|howtos=  
* Tests are run with multi gpu setup. For small cases like this, running it on a single gpu is actually faster: 17 seconds, which is +- 40% compared to 2.
* [[How to inspect object output attributes of an overlay using the measurement tool.]]
}}
}}
[[Category:Benchmarks]]
[[Category:Benchmarks]]
{{Water Module buttons}}
{{Water Module buttons}}

Revision as of 13:34, 16 January 2023

This page contains information how to inspect weir flow for Water Overlays. It also sets up a test case, which is described first.

Description

This test case consists of several weirs situated in a waterway, with each weir having different properties. All weirs are part of the same Water Overlay's simulation. There is no rainfall in this test case. Instead water flow is provided by inlets and outlets, which can be set up either variable or constant.

Weir test case top down.

Boundary and initial conditions

  • Waterways with weirs in the middle, separating two water areas.
  • One inlet per waterway providing an influx of water, situated in the water area on the left.
  • One outlet per waterway providing an outflux of water, situated in the water area on the right.

Parameter values

  • Manning’s n: 0.03 (uniform)
  • Model grid resolution: 1m

Technical setup

Waterways

Four waterways with a water depth of 2m and an angle of repose of 35 degrees, drawn with the following polygons:

  1. [187.0, -249.288], [418.0, -256.288]
  2. [413.0, -333.288], [189.0, -326.288]
  3. [194.0, -375.287], [411.0, -382.287]
  4. [404.0, -447.430], [194.0, -440.430]

Water Areas

Two areas divide the water ways into two sections:

  • Water area (left)
    • Rectangle shape: [301.0, -226.466], [158.884, -464.466]
    • WATER_LEVEL = 0.0;
  • Water area (right)
    • Rectangle shape: [424.884, -226.466], [301.0, -464.466]
    • WATER_LEVEL = 0.0;

Inlets


  • Inlet (Adjusting)
Inlet Q that is adjusting over time, visualized using the Measurement Tool's object attribute inspection.

Outlets

Each outlet is set up with the following attributes to remove the water that passed through the weir:

The outlets are situated at:

  • Outlet (Constant):
    • Rectangle shape: [414.554, -250.689] , [396.786, -253.873]
  • Outlet (Manual):
    • Rectangle shape: [410.115, -327.753] , [ 393.13, -330.9620 ]
  • Outlet (Adjusting):
    • Rectangle shape: [ 401.072, -442.541 ], [ 383.968, -445.520 ]

Weirs

Each weir is setup using a rectangular shape, and direction angle and a weir height and width:

Weir specific:

  • Weir (Constant)
    • Rectangular shape: [ 299.593, -248.328 ] , [ 302.229, -257.983 ]
  • Weir (Manual)
Weir height that is adjusting over time, visualized using the Measurement Tool's object attribute inspection.
    • Rectangular shape: [ 298.675, -324.174 ] , [ 301.613, -335.662 ]
  • WEIR_HEIGHT = [ 0 0 600 0.2 1200 0.2 1500 0.2 1800 -0.5 2400 -0.5 2700 0 ];
  • Weir (Adjusting)
    • Rectangular shape: [ 298.406, -437.681 ] , [ 301.142, -449.731 ]

Overlay settings

General parameters that have been used:

Output

Measured object graphs are displayed below:

  • Graph p1 case1 ukbm.png
  • Graph others p1 case1 ukbm.png
    • Graph of point 1 generated by the Tygron Platform on the left and generated by others on the right.
  • Graph p2 case1 ukbm.png
  • Graph others p2 case1 ukbm.png
    • Graph of point 1 generated by the Tygron Platform on the left and generated by others on the right.
  • Graph xslice case1 ukbm.png
    • Slice of the situation in the x -direction, generated by the Tygron Platform.

How-to's

Benchmarks button.png
Introduction button.png
Water Module
Benchmarks button.png
Getting started button.png
Tutorials
Benchmarks button.png
Overview button.png
Overview
Benchmarks button.png
Theory button.png
Theory
Benchmarks button.png
Benchmarks button.png
Benchmarks
Retrieved from "https://previewsupport.tygron.com/w/index.php?title=Weir_height_test_case_(Water_Module)&oldid=49277"