Model attributes (Water Overlay)

The Water Overlay's model calculations depend on a number of calculation-wide parameters. These parameters are available as attributes of the water overlay and can be modified as such.

Gravity (Water Overlay)

Max water depth m (Water Overlay)

Minimal culvert diameter m (Water Overlay)

Seepage fluctuation (Water Overlay)

Icon	Attribute	Unit	Range	Description	Default value
	ALLOWED_WATER_INCREASE_M	m		The amount by which the water level on a water terrain must increase before it is considered stressed by water. This is used to compute the WATER_STRESS result type.	0.4
	AVG_SHORE_WIDTH_M	m	0 to 10000 grid cells	With the surface water mode set to Grid Averaging, identified water average areas can be extended to include nearby shorelines within the configured distance.	3
	AVG_TERRAIN_WIDTH_M	m	0 to 10000 grid cells	With the surface water mode set to Avg Terrain, identified water average areas can be extended to include surrounding terrain within the configured distance.	1000
	AVG_TERRAIN_STORAGE_M	m	0 to 10000	When determining the water level of a land cell that will be averaged, the level will ignore the part that is reserved for storage.	0,05
	BRIDGE_ELEVATION	nominal	0 to 2	Specifies the mode by which bridges are include in the elevation model, used for the water calculations.	Lowest
	CULVERT_DEM_THRESHOLD_M	m	0 to 10000	The maximum distance a culvert's height can be below the terrain, for the terrain height to be adjusted to the threshold of the culvert.	10
	DESIGN_FLOOD_ELEVATION_M	m		Buildings in the model are assumed to have at most this height compared to the surface of the terrain. Greater values can create a more accurate model but will impact performance.	1
	GROUND_BOTTOM_DISTANCE_M	m	0 to 10000	Assumed distance under the surface terrain where the bottom boundary is situated.	10
	GROUND_WATER	nominal value		Whether and how water in the ground is simulated during the calculation.	Infiltration Only
	GROUND_WATER_DEPTH_M	m	-10000 to 10000	The default depth of ground water in meters.	1
	GROUND_WATERTABLE_WITH_SURFACE	boolean		Whether the ground watertable result type should also include the surface water level, when the groundwater levels are close to the surface.	True
	IMPACT_FLOOD_THRESHOLD_M	m		The amount of water a Building must experience before it is considered impacted by water.	0,1
	IMPACT_RANGE_M	m		the width in meters of the water next to or against the building that have to be flooded before the building is considered impacted by water.	3
	INCREASED_RESOLUTION	boolean		Load the DEM at twice the resolution.	False
	LIMIT_AREA	boolean		Whether calculations should occur in this area or not.	n/a
	LIMIT_RAIN	nominal value		Whether rainfall can be overridden by rainfall defined in rain areas across the project area.	0 (Entire map)
	MAX_WATER_BOTTOM_M	m + datum		The maximum height for the bottoms of water terrains. Any water terrain with a bottom at a higher datum height has its bottom lowered to this value.	10000
	MIN_MAX_ELEVATION	boolean		Whether to use highest and lowest elevations found for a grid cell for land and water respectively when interpreting the elevation model.	1.0
	OBJECT_ENTRY_CORRECTION	cells	0 to 3 cells	How many cells allowed to move a hydraulic structure's entry point when it overlaps with another hydraulic building.	2
	RISE_RATE_DISTANCE_M	m	0 to 10000	The water height threshold for computing the Flood rise rate result type.	1.5
	SEWER_OVERFLOW_THRESHOLD	fraction (m/m)	0 to 1	How much of a sewer's storage must be filled with water before the sewer overflows are allowed to overflow water.	0.9
	SHORELINE	boolean		Whether to automatically fill cells near a water terrain when there is a mismatch between the extend of the water terrain and the DEM.	True
	SHOW_DURATION_FLOOD_LEVEL_M	m	-10000 to 10000	The amount of water which must be exceeded in a specific location before the duration of surface water can be recorded. This is used to compute the SURFACE_DURATION result type.	0
	STABILIZER_ANGLE	angle (0-90°)	0 to 90	A partly flooded cell (especially at the edges of waterways) can become unstable when the angles in X and Y direction are too far apart. In this case the fluxes in U and V cannot easily be resolved mathematically while preserving balance. To prevent unrealistic fluxes from appearing, only the flux in the primary direction will be preserved. A stabilizer angle of zero means that all cells can be considered partly flooded cells, while an angle of 90 degrees will disable the stabilizer.	10
	START_DATE_MS	long		The date and time which is considered the starting moment of the simulation.	0
	SURFACE_WATER_EVAPORATION_FACTOR	factor	0 to 10	The factor by which the weather evaporation factor is multiplied to compute the amount of evaporation which takes place on the surface.	1.3
	SURFACE_WATER	Nominal value		Whether and how water on the surface is simulated during the calculation.	Shallow
	TIMEFRAMES	integer	1 to 1000	The number of intermediate results recorded during the calculation. Each timeframe becomes a snapshot of data which can be viewed and analysed.	10
	TIMEFRAME_TIMES	integer	0 to	The time of individual timeframes in seconds relative to the start date of the simulation.	0
	UNSATURATED_FRACTION	fraction		The initial fraction of the maximum storage capacity of the unsaturated zone which is filled with water.	0
	WEIR_DAM_MULTIPLIER	factor		The width with which the weir's dam should be generated perpendicular to it's direction, relative to its flow width.	3

---

Water Module

Water Module

Tutorials

Overview

Theory

Benchmarks

Group

Model attributes

Model attributes

Allowed water increase m • Avg shore width m • Avg terrain width m • Avg terrain storage m • Breach measurement distance m • Bridge elevation • Culvert dem threshold m • Design flood elevation m • Extended reconstruction • Ground bottom distance m • Ground bottom pressure m • Ground water • Ground water depth m • Ground watertable with surface • Impact flood threshold m • Impact range m • Increased resolution • Infiltration factor s

Limit area • Limit rain • Max infiltration m • Max water bottom m • Microrelief storage fraction • Min max elevation • Object entry correction • Prequel surface level relative • Rise rate distance m • Sewer overflow threshold • Shoreline • Show duration flood level m • Stabilizer angle • Start date ms • Surface water • Surface water evaporation factor • Timeframe times • Timeframes • Unsaturated fraction • Weir dam multiplier • Weir move interval s • Weir move range m • Weir move step m

Related

Building attributes • Hydrological features • Hydraulic structures •  Terrain attributes • Results • Simulation data